Vintage Mustang Forums banner

Search results

1-20 of 128 Results
Advanced Search
  1. 83 Mustang 4 speed.....Will it work in my 70 ?

    Vintage Mustang Forum
    Thanks much guys.....You convinced me !!!!!!!!
  2. 83 Mustang 4 speed.....Will it work in my 70 ?

    Vintage Mustang Forum
    I can have an 83 Mustang 4 speed tranny from a friend. Will it work in the 70 fastback that I'm building ? I realize I will need, bell housing, linkage etc ! I just think it would be a good start. I have a 351 Cleveland that came with a clutch & flywheel ! Yes or no ?
  3. Looking for a Shelby expert in Minnesota

    Vintage Mustang Forum
    Unique Specialty & Classics in Mankato.....507 386 1726 talk to Jay
  4. Rear Seat for a 70 Fastback

    Vintage Mustang Forum
    marlarson.....The ad reads "I have the rear seat from a 68 to 70 cougar or mustang, it was reupolstered and never installed in the car" It looks real nice in the picture ! I'm sure it's not a fold down but I don't really care as I have no seat at all for the 70 fastback I'm working on. The price...
  5. Rear Seat for a 70 Fastback

    Vintage Mustang Forum
    I found a real good deal on a rear seat. Ad says 67-68 or 69-70 mustang or cougar ! would they fit my 70 fastback by chance ?
  6. 68 J Code Heads

    Vintage Mustang Forum
    Thanks Hemikiller !
  7. 68 J Code Heads

    Vintage Mustang Forum
    Does anyone know if 68 J code rockers are adjustable or are they like my 67 302 ?
  8. Window Roller Rivets ?????

    Vintage Mustang Forum
    Thanks for the input.....I think I found the rivet studs at NPD. I will know when I get them !
  9. Window Roller Rivets ?????

    Vintage Mustang Forum
    Thanks 22......I will check that out. I still don't understand why there are tons of the 11/16ths roller replacements but no 1'' !!!!!!
  10. Window Roller Rivets ?????

    Vintage Mustang Forum
    I know this is an age old issue, but has anybody found a source for the rivet stud for the rollers on the window ? My rollers are fine (the 1" ones on the window not the scissor) but the some of the studs are no longer attached. I've searched and can't find a vender that sells the correct studs...
  11. 67 Front Fender Fitment

    Vintage Mustang Forum
    Thanks for the advise Woodchuck.....meanwhile I'm going to keep searching for the post where someone had the same problem !
  12. 67 Front Fender Fitment

    Vintage Mustang Forum
    Yes Woodchuck.....It's a 67 ...there are no nuts, only bolts. I can have them all in & the one inside by the pillar & everything looks good until I push the bottom in to meet the rocker panel. Then the fender raises up at the cowl area !!
  13. 67 Front Fender Fitment

    Vintage Mustang Forum
    ????????anyone ?
  14. 67 Front Fender Fitment

    Vintage Mustang Forum
    I bought an after market right front fender. It fits almost perfect as far as body lines etc. My problem is when I bolt it up in -place and bring the bottom in to meet the rocker panel it raises up the top of the fender by the cowl. I'm guessing it's because of the vertical brace inside of the...
  15. 67 Fender Lettering Template ?

    Vintage Mustang Forum
    Thanks 4ocious.....Perfect !!!
  16. 67 Fender Lettering Template ?

    Vintage Mustang Forum
    Is there such a thing ?
  17. 67 Door Panels

    Vintage Mustang Forum
    Not the answer I was hoping for but thanks for the reply !!
  18. 67 Door Panels

    Vintage Mustang Forum
    I want to replace the cardboard door panel backing with 1/8" masonite hard board. My question is, how is the covering attached to the cardboard backing...some sort of glue ? can I remove it without ruining ? The panels are perfect except for a few clips have pulled thru the cardboard !!!
  19. 67 Vent Window Run Channel

    Vintage Mustang Forum
    Thanks 4ocious.....found it !!!
  20. 67 Vent Window Run Channel

    Vintage Mustang Forum
    How hard is it to replace the vent window run channels ? I have the assemblies out ! Is there a video somewhere ?
1-20 of 128 Results
Top