Vintage Mustang Forums banner

Search results

1-20 of 284 Results
Advanced Search
  1. 67 Standard pedal assembly

    Classic Mustang Wanted Ads
    I need the complete assembly
  2. 67 Standard pedal assembly

    Classic Mustang Wanted Ads
    I need the whole unit with both pedals.
  3. 67 Standard pedal assembly

    Classic Mustang Wanted Ads
    I need a pedal assembly for a 67 power disc standard shift, MUST BE 67 NOT 68
  4. Shelby Lemans stripe Question

    Vintage Mustang Forum
    Use the measurements in the back of the Branda Mustang catalog and you will be ok, the white is actualy a Chevrolet white, if you are really interested i could get the paint code for you.
  5. Will paint stick on my '67 wide grille opening moldings?

    Vintage Mustang Forum
    Use a SELF ETCHING primer not just primer!
  6. Brake Booster ?

    Vintage Mustang Forum
    I installed a Midland Ross Booster on my 67 and the brake pedal is about 1/2 way down, i have not yet installed the master cylinder, is this normal? will the pedal return after the brake system is complete? this car has been apart for years and i am not sure if some of the parts are...
  7. Intake question

    Vintage Mustang Forum
    I am using an original Shelby intake on a 289 and was wondering why there are no rear water passages? Whats a good intake that does have the rear water passage for a midrange 2000 to 4000 rpm boost, i am running a mild cam, hyd lifters, headers and 4100 1.08 carb and MSD dist.
  8. Header Gaskets

    Vintage Mustang Forum
    What is the best header to block gasket for a 289??
  9. Powermaster Alternator is HOT

    Vintage Mustang Forum
    What gauge wire are you using, it should be at least a 10 or larger.
  10. Interesting car show fund raiser

    Vintage Mustang Forum
    Local show gets a car donated by local boneyard and drains all the fluids, then tie the gas pedal down and start the engine, they sell chances on how long it will last, 1/2 goes to winner 1/2 goes to charity, it's surprising how long they last.
  11. WANTED: Shelby project or 67 Shelby GT500 clone

    Classic Mustang Wanted Ads
    I might consider parting with my 67 GT500 #1833 in the Shelby Registry, It has undergone a complete new suspension and paint with lemans stripes, has a set of Magstars and a set of tenspokes, all Shelby equipment, comes with a balanced 428CJ with 2X4 BBLs, new brake lines new fuel lines,rebuilt...
  12. Fold down parts

    1967 through 1968 Mustang Parts For Sale
    Any chrome trim pieces, i need the wide one that the latch goes in for 67 or will take whole set if you would rather not seperate it, please e-mail me [email protected]
  13. Anodizing Removal

    Vintage Mustang Forum
    Thanks guys
  14. Anodizing Removal

    Vintage Mustang Forum
    Someone had a tip for removing the anodizing on aluminum before buffing but i cannot seem to find it with a search, could you let me have it again. Thanks
  15. 66 5.0 swap

    Vintage Mustang Forum
    Is there a website or a book that details the 5.0 swap into a early 66 Mustang
  16. Crate Engine Changeover??

    Vintage Mustang Forum
    Thanks for the information, looks like a lot of little things and not to many BIG things to look out for.
  17. Crate Engine Changeover??

    Vintage Mustang Forum
    Whats involved in installing a new 5.0 Ford Crate Motor in a 66 that has a 289 and toploader 4sp, i would like to keep the trans and keep it carburated, where is the best place to purchase one of these engines in the New England area and an idea of total cost of the project??
  18. lifter problem update, Long

    Vintage Mustang Forum
    as posted before i was in the process of removing roller tipped rockers that i could not quiet down when i found what i thought was a collapsed lifter, after removing the lifter i found the bottom was worn away almost a 1/4 inch and the ones on either side of it are chipping away, this motor was...
  19. Collasped Lifter

    Vintage Mustang Forum
    I turned the motor over till the battery went down and all the others pumped up fine, i added a 1/2 qt of Rislone to the oil recharged the battery and turned it over again till the battery went down and will check it out tonight to see if it loosened up that lifter. As per the other post about...
  20. Collasped Lifter

    Vintage Mustang Forum
    I could not quiet down the roller tipped rockers, i even changed out the hyd lifters after complaining to Comp Cams who told me there was dirt in the new lifters, i have to friends who had there motors one 289 and one chevy 350 rebuilt by the same guy with the same Comp Cams cam and lifters with...
1-20 of 284 Results
Top