Vintage Mustang Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 33 Results
  1. Vintage Mustang Forum
    Hi. I pulled what look to be factory original Kelsey Hayes front disc brakes from my 65 Mustang Convertible. I regularly drive the car, so the brakes are working properly, but they look like it’s time for a refresh. I am planning to rebuild them if I have a complete OEM kit. The spindles...
  2. Vintage Mustang Forum
    Hello, While i've got my engine out, i've been cleaning up the engine bay for a paint. In doing that, i've noticed that one of my strut rod brackets is cracked (as photo). Drivers side. From what i can tell, it is isolated to just this. Generally, the frame actually looks pretty clean. So...
  3. Vintage Mustang Forum
    Does anyone know the correct White Paint color code for a 1965 Mustang dash cluster background paint. I would prefer the concour color but am not willing to use a rattle can white such as Krylon Flat white. I am looking for a supplier of 8oz/16oz to a pint for use in a spray gun. Where can I...
  4. Vintage Mustang Forum
    Hello. I just pulled a 302 out of a foxbody mustang. This motor has a more modern alternator (2 plugs, one being for the voltage regulator). My question is, how can I make this work with stock 1966 mustang wiring?
  5. Vintage Mustang Forum
    I bought a replacement gas cap, but it didn't come with its own ring. How do I properly remove this and place it on the new cap?
  6. Vintage Mustang Forum
    Hello. Getting ready to put my 302 with aod into my 66 mustang. Using the original 6 cylinder automatic drive shaft. Do I need a different slip yoke for the aod? Like I said, the one on there now was for a C4.
  7. Vintage Mustang Forum
    How much does everyone worry about mouse nests in their frame rail when patching? I’m doing a couple patches by the front eye bolt hole and when I cut out the bad metal, I could see a mouse nest in the rail where the rail starts to arch over the wheel. I cut a couple holes in this area and...
  8. Vintage Mustang Forum
    Hello. While taking the front end apart I broke the ground wire going to the passenger parking light so I ordered the below part: My question is, it doesn’t look like these plugs come with the ground wire for the parking light (supposed to come out of the plug and have a female end on it to...
  9. Vintage Mustang Forum
    For a '66 Mustang GT, were the "MUSTANG" fender letters supposed to be entirely chrome? This photo shows some of the letters appearing to have black filler, although certain vendors claiming to be selling original letters pulled from actual '66 GT's show them all as chrome. Thanks for your help!
  10. Vintage Mustang Forum
    I recently purchased a 1966 Mustang factory A-code GT coupe in its (repainted) original factory color, springtime yellow. It has a vinyl top, so I tried to include photos of Mustangs with the same color/top. I'm considering getting it repainted to one of these options, and I was curious what...
  11. Vintage Mustang Forum
    Hello. I installed my new shock tower and looking at the holes where the motor mount bolts in, the holes aren’t sleeved like my original shock tower. Is this okay? It is thick steel, so it’s probably okay, but just want to make sure. Like I said, the old one has sleeves in the holes for extra...
  12. New Member Introductions
    Greetings, The obvious 1st step in re-restoring my 1966 coupe seemed to be joining VMF, so I'm honored to be here. I & my Mustang are originally from Ohio but have recently relocated after 15 years in California to SW Missouri following a cross-country pilgrimage along Route 66. Purchased by...
  13. Vintage Mustang Forum
    I recently got a console for my 1965 Mustang from Kentucky Mustang. The kit didn't have any instructions so I went looking for anything I could. I only found one video that was helpful (link below) but I really didn't like the way they installed the door. So I made this video. There are several...
  14. Vintage Mustang Forum
    My Mom has a 1966 Mustang 289. It used have the factory 2 Barrel code C6DF-F. From my understanding the -F was specific to the California sold Mustangs that had the thermactor installed. Recently it wasn’t running right and her notsobright s/o took it to autozone and replaced it with the wrong...
  15. 1964 1/2 through 1966 Mustangs For Sale
    Hi all, Have a 1966 c code fastback for sale in wisconsin. Has a 302 in it that runs well with electronic ignition on it, originally manual trans car and still has clutch pedal but c4 auto trans in the car. 8 inch rear, has newer tail panel and right rear quarter previous owner installed. Needs...
  16. New Member Introductions
    Hi, I am new here, my first car was a 1976 Cobra II white with red stripes, I have always liked Mustangs, there were some other first generation mustangs in my family. I bought it from a Ford employee in 1978, it had a four cylinder with an automatic transmission and vinyl seats, it looked cool...
  17. Vintage Mustang Forum
    I am a newb here. After 40 years of dreaming, I am finally a vintage Mustang owner. I recently purchased a nearly all-stock 66 coupe 289 2bbl C4. On one of our 1st outings with her, we were stuck in a VERY long line to get into a drive-in theater and I realized the temp gauge was moving up...
  18. Vintage Mustang Forum
    1966 289 2 barrel 3 speed auto So here's my issue as I was test driving my car: When cold my engine starts right up and when I put it gear it starts driving ok But as I am driving if hit the gas (let's say more than 20% in the Throttle) the engine does not respond well it does what he call in...
1-20 of 33 Results
Top