Search Results for ‘mustang 66’

Need some thoughts on the rust on this 1966 mustang. How hard and how much to fix? Steps on fixing?

Hello all, We have a freshly rebuilt 289 (60 over now) that is running smoothly. The cam was just broken in, and the car now can move under its own power (first time in 5 years). Before this rebuild, we had PCV from the passenger side into the air cleaner. Now, we have it coming from the driver...

Hello. Does anyone else have trouble tightening the pitman arm to centerlink boot for power steering? At a certain point the joint inside the centerlink just spins and you can’t tighten any further

Hello everyone, anyone know a good shop in the Fresno area or nearby that works on classic Mustang’s ? Or if anyone can help me with a couple troubles I ran into with my 66 Mustang. I took it to a shop because the carburetor was having trouble and they said I would need a new carburetor and that...

Have a ton of parts for sale, motivated to sell. Rebuilt C4 tranny (2300 dollar rebuild), 200 straight 6 engine (running), spare carbs and distributors, 7.25 inch rear, 8 inch rear, front steering components, 6 cylinder spindles, 6 cylinder engine mounts, exhaust, etc. Ask and I might have it...

So I pulled one of a spark plug out and the bottom part looks very black. I’m assuming that’s not how it supposed to be. So I need help on that... like what’s the problem and how to fix it? second problem that I’m seeing is coolant that seemed like it was around the oil pan. I cleaned and...

So I have a 302 from 83 and C4 transmission in mustang 66. In many problems I’m facing a new problem. So when I test drove the car today it was running very heavy under acceleration. Everything is good. Transmission and of course engine too but I feel like it’s just some adjustments that I’m not...

So I been working on my project that I have. It’s mustang 66 with 302 and c4 transmission. Today I installed the transmission back in following all the correct directions. Now car won’t go in gear at all.... I move the shifter but car is not making any section of any gear. My sifter linkage is...

Here we go with a new problem! So I have 302 engine in 66 mustang and it’s leaking engine oil when I try to drive it and floor the gas pedal. No leaks at all while the car is idle/running. I can’t even see where it’s leaking from unless I put a small camera and record while driving. No gasket...

I recently got EdelBrock super victor intake. It’s not fitting properly. One side sits then other side doesn’t sit. I don’t know if this is possible but can you grind the head down a bit to make it fit? Or that’s a no?!?!

It’s been super long that my thermostat won’t stop leaking no matter what I do. I even bought a new thermostat and replaced it but still the same problem. Tried putting the sealer around the thermostat so stop to leak but even that doesn’t work. Tried both ways ... with or without gasket...

Hi I just have a quick question. What’s the best way to run the electric fan in 66 mustang that will work with the small switch that I can use to turn the fan on and off. Thank you

I have a mustang 66 and it has a 302 engine in it. Ever since I started the car it’s not turning off with the key. It turns on with the key but not off. I’m running the wire for coil from ignition ( red wire) is that why it’s doing that? If so then where should I run the coil wire from?

I’m very concerned about my balancer does anyone know why my balancer is shaking a bit? When I idle the car the balancer feels spinning funny and not spinning solidly. I have a mustang 66 and it has a 302 in it. Please help because I’m very concerned. I don’t think I can upload a small clip...

Hello Everyone, I have a mustang 66 and I recently put 302 engine in it. When I got the engine it didn’t have eccentric and correct timing cover for mechanical fuel pump to go in. So I bought 69 mustangs timing cover and stuff. I installed 1 piece eccentric and it wasn’t rotating at all and...