Vintage Mustang Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 25 Results
  1. Vintage Mustang Forum
    This may be more of a general electrics question rather than Mustang specific, but it's got me scratching my head a bit. Basically, I have fitted LED bulbs throughout my 66 Mustang. Turn signals work exactly as they should, unless that particular light (side light / park light) is already on...
  2. Vintage Mustang Forum
    Hey guys. I'm wiring my 1967 Mustang with American Autowire's harness. I'm connecting my 2-speed wiper motor to the harness and I need to figure out which wires (black, white with red stripe, lt. Blue, & red with lt. Blue stripe) do what. Attached below is a picture of the AAW wiper motor wires...
  3. The Fox Hole
    So I have a 1990 mustang and I have recently installed a new tach with a shift light since the stock one is pretty jumpy and the moment I also have a kill switch for the car wired to the ignition coil. So here’s my main question is there a type of relay that will open( turn off) a circuit when...
  4. Vintage Mustang Forum
    I’m hoping someone can point me in the right direction or even just tell me where to get started with this problem. Full disclosure, I’ve never done any wiring so I know next to nothing on this subject. You’ll probably need to explain like I’m 5. Ok, here’s the issue: my speedometer and dash...
  5. Mod and Custom Forum
    Hi All, Hope maybe someone here can maybe help me with a dilemma I have been dealing with the last couple of days. So I did a Inline 6 to V8 conversion on my 65 convertible and I am almost done.......finally lol. One of the last big issues I am dealing with on my build is when I turn my...
  6. Vintage Mustang Forum
    Rewiring my 68 Mustang Hi all, this is a brief summary of my rewiring extravaganza of my 1968 inline 6 Mustang (auto without AC). The intent is to help others who are trying to rewire their own classic car. I do not have any mechanical background and no electrical engineering background...
  7. Vintage Mustang Forum
    I have a 66 mustang with a 289, mild cam, edelbrock performer 500cfm carb, performer intake manifold, and almost everything else stock. I also have a 2 10-inch subwoofers powered by a 1200 watt amp with a retrosound head unit running on the stock alternator, but that’s about the only electric...
  8. Vintage Mustang Forum
    Alright guys i need the power of the internet to help me with some opinions. I have a 68 mustang coupe that i have recently upgraded the headlights to led Halo DRL with turn indicators. (See attached image). And im waiting on the fog lights to come in. While i am waiting i want to get the wiring...
  9. Vintage Mustang Forum
    I need help identifying the 8 wires hanging down from my steering column the color coding of the wires does not match the schematics that I have. Which wire is for what
  10. Vintage Mustang Forum
    Hey folks, Currently swapping out the gauge cluster on my 68 convertible w/o AC for a rebuilt analog version (no tach). I pulled the cluster and labeled all the wires so I know where they go back. while doing this I thought about the reconnection process… does anyone switch from the 90 degree...
  11. Vintage Mustang Forum
    Hello. While taking the front end apart I broke the ground wire going to the passenger parking light so I ordered the below part: My question is, it doesn’t look like these plugs come with the ground wire for the parking light (supposed to come out of the plug and have a female end on it to...
  12. Mod and Custom Forum
    Hi guys! Been on the forum as an observer for quite some time, but haven't been able to find an answer about this one so I made an account and here I am. I've got a 67 Mustang I6, and the turn signal wouldn't stay locked in the right position and the horn wouldn't work. Figured it was that...
  13. Vintage Mustang Forum
    Greetings- Im replacing my ignition switch on my 65 Mustang convertible pictured below with a Painless wiring kit. The current set up doesn't have the insulated switch pig tails but the new set up will. Current set up just has the wiring push pins that push into the back of the ignition switch...
  14. Vintage Mustang Forum
    I'm putting in a push button start system until I can get my hands on lower lock actuator for a tilt column. I figured out all the wiring except for the purple/white and red/white wires. I looked at the wiring diagram and I believe they should be connected to blk ground in run, but I'm not 100%...
  15. Vintage Mustang Forum
    I want to replace my dash wiring harness. But I don't like how much that cost... I have a rather large amount of wire for some reason. I was wondering if anyone has made there own harness befor and if so was it hard?
  16. Mod and Custom Forum
    I am in need of some help with wiring my alternator - starter - battery in my 65 Mustang. I am doing a full restomod (car has been gutted and is being completely built back up) and can't seam to get a concise answer on the best way to wire my 140a 1-wire alternator with a PMGR Starter and my...
  17. Vintage Mustang Forum
    Hey everybody, I was doing some wiring yesterday because I’m doing a 5.0 EFI swap into my 1965 Mustang. When I came to wiring up the new gauge cluster, I had to run a wire from the cluster straight to the left turn signal. The wire ran from the gauge cluster through a grommet in the firewall...
  18. Vintage Mustang Forum
    im working on my 69 mustang and for the winter I decided to take the dash apart and work on why my instrument panel lights aren't working. Originally I would turn my headlights on and they had a flickering issue and would eventually stop flickering, and only the light for the alternator...
  19. Vintage Mustang Forum
    Lord help me not strangle myself with these wires. I have the AAW kit installed in my 67 mustang. My rear drivers side turn signal light is not working when headlights are on — My passenger side is working perfectly. I have grounded it at least 6x. I have used a dremel to chip paint, I’ve...
  20. Vintage Mustang Forum
    I'm working on starting my 1966 Mustang after it has been sitting for several years. It has a 289 v8 and automatic transmission. I've gotten a new starter, starter solenoid, voltage regulator, points, rotor, spark plug wires, and plugs. It cranks over just fine, however, I haven't been able to...
1-20 of 25 Results
Top