Vintage Mustang Forums banner

69,70 Hood Mouldings

Jump to Latest Follow

1 - 3 of 3 Posts
G

·
Registered
Joined
·
655 Posts
Discussion Starter • #1 •
Will the '70 moulding fit the '69?I have a new repo '69 molding & it's not real flash,but I can get hold of an nos '70 mould & was hopeing it would fit.Any differences?
Greg

Never go into a battle of wits unarmed!
http://albums.photopoint.com/j/View?u=1589603&a=12101731&p=45958396&Sequence=0&res=high.jpg
Regards From the Great South Land.
 
G

·
Guest
Joined
·
0 Posts
#2 •
No, the '70 molding has a different profile to match the different '70 grille moldings. It would "fit", but it would not match your other '69 front end moldings.
 
G

·
Registered
Joined
·
655 Posts
Discussion Starter • #3 •
Looks like I'll have to doctor the repo mould.Appreciate your help.
Greg

Never go into a battle of wits unarmed!
http://albums.photopoint.com/j/View?u=1589603&a=12101731&p=45958396&Sequence=0&res=high.jpg
Regards From the Great South Land.
 
1 - 3 of 3 Posts
Recommended Reading
Read More

  1. Show me your engine bay!!

    Vintage Mustang Forum
    Since my car is in pieces and I’m going to rebuild the 289, I need to get some ideas on how to “dress” the engine bay. I don’t want to end up with an abomination of blue, red, yellow, black and chrome - so pop your hoods! I’ll get it started ;)

  2. Turn signal grief

    Vintage Mustang Forum
    Just finished replacing my turn signal switch for the third time— I go to test out the blinker, and it starts smoking. Doesn’t work at all now. 90 dollars and three switches later, I’m getting REALLY TIRED of these [email protected] things... After the second one blew out, I did some extra research. People...

  3. 68’ Differential Housing Question

    Vintage Mustang Forum
    8” Rear on this 68 Coupe and I was wondering if this front part of the carrier where the pinion is (smaller one with 3 bolts showing in photo) Has it’s own gasket underneath and can unbolt without taking the entire carrier and axles out. It appears it’s starting to seep a tiny bit now that...

  5. Speedometer cable and drive gear on top loader

    Vintage Mustang Forum
    Ok , so after a lot of help on a different thread about gear ratios where I was not going to be happy with the close ratio top loader I was putting in to replace my 3 speed, I sold the close ratio and purchased a wide ratio with the hurst shifter and linkage, supposed to have been rebuilt and...

  6. Can you recommend a good mechanic in Manassas/Northern Virginia?

    Vintage Mustang Forum
    I have a stubborn engine vibration issue. I think its the the damper, but am intimidated a bit by the install process. I'd have no issue taking it to a mechanic knowledgeable on these old 289s. So if you know a good tech in the Manasass/Norther Virginia area, please let me know.
Read More
About this Discussion
2 Replies
1 Participant
Last post:
GregOShea
Vintage Mustang Forums
A forum community dedicated to vintage Ford Mustang owners and enthusiasts. Come join the discussion about restoration, modifications, NOS parts, troubleshooting, VIN codes, and more!
Full Forum Listing
Explore Our Forums
Vintage Mustang Forum General Discussion (Non-Vintage Mustang) Mod and Custom Forum Classic Mustang Wanted Ads Concours Forum
Popular Communities
Community avatar for Home Entertainment
Home Entertainment
1,280,000+ members
Join
Community avatar for Mountain Bike Reviews
Mountain Bike Reviews
450,000+ members
Join
Community avatar for Working From Home Forum - New!
Working From Home Forum - New!
25+ members
Join
Top