My first post here

852 Views 8 Replies 4 Participants Last post by Guest, Apr 4, 2001

Discussion Starter · Apr 3, 2001

Hi all,

My first post here, nice to have this new look to forum. Here in Finland snow is finally begin to melt and tarmac is coming to visible. I have worked on garage to get my 'stang to streets, only little brake problems exists and putting starter and battery to car. Brake problem is quite nasty because pressure control valve won't keep fluid inside, I now that seal has gone bad. Now I only have to get new from autopartswarehouse hope to find one. Ok, that's all. I wish for all you very nice spring and summer time, see ya soon!

Regards,

Ari
Pattijoki, FINLAND

Ford Mustang HT '66 A-code 289, 4-speed manual. Hi-po parts: Edelbrock RPM cam/heads,Crane roller rockers,Ford Motorsport push rods,Weiand Stealth intake,Tri-Y headers with 2.5" pipes/Flowmaster 2-chamb. mufflers. 8" 3.50:1 rear with detroit locker.

Save

1 - 9 of 9 Posts

Huskinhano

· #2 · Apr 3, 2001

Welcome! there are quite a few members from Finland on the forum. You guys allways seem to have nice Mustangs. How's it for getting parts for them over there?

Tom
You can do anything you want to......ONCE!
aka "my 66 coupe"

Save

TFOB

· #3 · Apr 3, 2001

Welcome to the VMF show.

a lot of good people hang out here.
Lots of good advice, and a few laughs. Hope you enjoy the ride.

http://albums.photopoint.com/j/View?u=1603896&a=12227373&p=44503083.jpg
73 351C C6 3.25 T-lock
Jesus is all the world to me!
Mustang's are just a Hobby
http://www.folksite.com/TFOB

Save

G1967T

· #4 · Apr 3, 2001

Welcome. Can you post a picture of your car?

Russ

http://albums.photopoint.com/j/View?u=1595962&a=12199293&p=44747301.JPG

Save

Discussion Starter · #5 · Apr 3, 2001

welcome, friend!

Save

Discussion Starter · #6 · Apr 4, 2001

Picture of car is in my homepage http://www.geocities.com/akatajam/

There is also pictures of cowl repair etc.

Ari

Ford Mustang HT '66 A-code 289, 4-speed manual. Hi-po parts: Edelbrock RPM cam/heads,Crane roller rockers,Ford Motorsport push rods,Weiand Stealth intake,Tri-Y headers with 2.5" pipes/Flowmaster 2-chamb. mufflers. 8" 3.50:1 rear with detroit locker.

Save

G1967T

· #7 · Apr 4, 2001

Nice car... I am impressed! Stick around, I think you belong here also. Your English is just fine, and your Mustang does allot of the talking for you.

Russ

http://albums.photopoint.com/j/View?u=1595962&a=12199293&p=44747301.JPG

Save

Arto65FB

· #8 · Apr 4, 2001

Where you have been? This might be your first post in the new forum, but I have already advertised your cowl repair earlier when advice was sought. BTW, Corral is on schedule, it will posted before American Car Show.

Door handle first when cornering

Save

Discussion Starter · #9 · Apr 4, 2001

Hi Arto,

I'v been busy on my computer and dvd videos.

My mustang is in quite good shape, not much needed advices with it. That's why I haven't watched this forum. I hope this summer will be much better than last. I look forward to get new corral to my hands soon

Ari

Ford Mustang HT '66 A-code 289, 4-speed manual. Hi-po parts: Edelbrock RPM cam/heads,Crane roller rockers,Ford Motorsport push rods,Weiand Stealth intake,Tri-Y headers with 2.5" pipes/Flowmaster 2-chamb. mufflers. 8" 3.50:1 rear with detroit locker.

Save

1 - 9 of 9 Posts

This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.

Top Contributors this Month