G
Guest
·Guest
Joined
·
0 Posts
Can someone lead me to some direction on how to perform the Shelby A arm relocation on my 65 coupe? I plan on installing 620 rate springs. Can I still do this without any clearance problems? Thanks.
Shelby A Arm relocation.
1 - 3 of 3 Posts
G
Guest
·Guest
Joined
·
0 Posts
There is a very good explanation of how to do it in the back of the Tony Branda
catalog. Yes you can do this without creating clearance issues.
jimbo
M.C.A.# 50000
http://albums.photopoint.com/j/View?u=1575692&a=11979479&p=43517165.jpg
catalog. Yes you can do this without creating clearance issues.
jimbo
M.C.A.# 50000
http://albums.photopoint.com/j/View?u=1575692&a=11979479&p=43517165.jpg
Joined
·
4,092 Posts
I have 215 60 R15 tires with 620 springs and the lowered control arms and have been very happy. Definately no rubbing what so ever.
I have templete on my website.
[color:black]1966</font color=black> [color:red]V8 Coupe</font color=red>
http://www.geocities.com/2bav8
I have templete on my website.
[color:black]1966</font color=black> [color:red]V8 Coupe</font color=red>
http://www.geocities.com/2bav8
1 - 3 of 3 Posts
Join the discussion
Recommended Reading
-
First real outing with the 67’
Vintage Mustang ForumAfter what seemed like forever (since October lol) finally got things straight and was able to take her out for more than a 5 mile test ride. A little Picnic lunch by the Tred Avon River then a ride over to Oxford for some ice cream a ferry ride across the river and the long way home. Felt...- 18
- 322
-
jjpish68 · updated
-
FMX Hesitates Going Into 3rd Gear with Heavy Foot
Vintage Mustang Forum1971 Mach1 351C with FMX. Grabber yellow with Mach1 flat black treatment and stripes. Great car! I bought the transmission used for $250 and it works/shifts fine when I drive car normally, however if I jump on it or punch it, the tranny slips and engine revs up for about a second before shifting...- 2
- 32
-
Rumblefish351 · updated
-
1965 Power Steering leak question
Vintage Mustang ForumMy new to me 1965 convertible has a power steering leak, I think this is a fairly common problem. The control valve is leaking. My question is should I remove it and install a rebuild kit, or just replace it. It seems to be a bit pricy at over $300, a good kit is around $70. Just want to...- 2
- 43
-
Bleeding brakes. Frustrated, got to vent.
Vintage Mustang ForumSo I'm trying to bleed my brakes after replacing my master cylinder. I got a 65 6 cylinder with four wheel drums. I've gone around the car 5 times trying to get the brakes bled. I'm doing it with my wife doing the press, open, close, release method and got out all the big bubbles I could see...- 14
- 282
-
jerky at slow speeds
Vintage Mustang Forum64must Registered Joined May 15, 2014 37 Posts Discussion Starter • #1 • 18 h ago My 1964 1/2 289 mustang starts and idles ok. It backs out of the driveway ok. Accelerating slowing the car is very jerky. Stomp on the gas pedal and it takes off quickly and smoothly. The car has a fresh tune...- 1
- 59
Join now to ask and comment!