The one on the bottom left looks like a windshield washer fluid pump.

 

Out of all of it, the only things I recognize is the rubber bumper (picture 3) for the fold down seat, and the power steering pump bracket in the center of the last picture.

The fold down seat bumper is toast. It's suppossed to have a screw sticking out of it. Toss it in the garbage or use it for a door stop. New ones are cheap.

The PS bracket bolts to the back of the pump. It's a worthless bracket that only works with a concourse correct high pressure line. The one in the picture seems extremely flat, which they normally aren't.

 

The black disc in the first pic looks like the plate to hold down the spare tire.

 

The two long rectangle pices are inserts for trunk lid hinges (witch i just happen to need, i lost mine in 10 years of storage and moves) so let me know if you want to get rid of them, i'll have to check on price, i couldn't tell you what they're worth.

The roung metal object with rtv appears to be the lock ring on a gas tank for sender/pickup.

 

The thing with your finger on it is a block heater or oil heater .

 

You are correct on the tilt away vacuum piece. It's a solenoid that would fit on a '67 for sure and maybe the '68-'69 as well. It is missing its power and ground wires however.

 

The piece your finger points to is a heat source for the choke on the carburetor.

 

I'm sure the disk is a hold down for the spare. The loop is probably a heater for the engine oil or water, does it have electrical connections?

 

Dibs on the PS pump bracket!!

 

GregB is correct on the piece with the finger on it, its a heat stove for the choke on at least 351C motors.

Carl

 

to the left of the rubber bumper, looks to be bolts with washers (sorry - couldn't resist)

 

to the left of the rubber bumper, looks to be bolts with washers (sorry - couldn't resist)

They look like the fender bolts that are hidden just above the door hinge

 

Since you identified them then you can have them :highfive: PM me with your address and i'll see if i can cook something up for cheap shipping.

 

You are correct on the tilt away vacuum piece. It's a solenoid that would fit on a '67 for sure and maybe the '68-'69 as well. It is missing its power and ground wires however.

Thats kinda what i figured. It has the male blade sticking out on the end of the black tube part. Is that the power or the ground? Where does the other wire plug in? It still retains the factory rivets so it hasn't been tampered with. What do these normally run for pricewise?

 

Anyone care to explain what motor this powersteering bracket is correct for? Neither of my 70 cars had them with one being a 302 and the other 351w. What years did they come from? Oh and the bracket isn't flat, its just the picture.

 

GregB is correct on the piece with the finger on it, its a heat stove for the choke on at least 351C motors.

Carl

What does this bolt to, the manifolds? Also, where does the loop go into? The loop is removable and there aren't any electrical connections for it to be a block heater. Just two bolt holes and two holes for some kind of tubing. Are these pretty easy to come by?

 

Did the fender bolts differ in that area compared to the ones on top? The bolts are two inches long and have a funky washer that is square with the corners sticking out.

 

Thanks to all who provided very helpful information (except the obvious bolt response :joker!!!! You guys are awesome. So far one piece goes to the spare tire, one is for a tilt column, two brackets are for the trunk hinge, the round ring might be too small to be a retainer for the fuel tank sender but i'm not sure (2.5" outside diameter), bumper for folddown, power steering bracket, choke stove piece, a mystery wire that may be some kind of heater, mystery grommet, and two mystery bolts. Thanks for all the help everyone! :highfive: If you need any of these pieces let me know. I may or may not use the PS bracket depending on what it is correct for. Feex don't lie and say it isn't correct for my motor so you can buy it from me :joker: Just kidding.

 

The mystery bolts look like vent window frame bolts to me. The grommet is a pcv grommet

 

The thing with your finger on it is a block heater or oil heater .

Close, it's the choke pre-heat tube for a 70-73 351C. Bolts into the mnaifold on the passenger side by the carburetor pad.

 

GregB is correct on the piece with the finger on it, its a heat stove for the choke on at least 351C motors.

Carl

What does this bolt to, the manifolds? Also, where does the loop go into? The loop is removable and there aren't any electrical connections for it to be a block heater. Just two bolt holes and two holes for some kind of tubing. Are these pretty easy to come by?

the choke stove slides into the manifold & into the head right in the center ofthe head, on the ps ofthe intake. it heats up from the exhaust gases. this is the pre curser to EGR valves(installed in the same spot)

 

I would say the rubber grommet is for a valve cover pcv hole and the ring with RTV on it is off of a styled steel or Magnum 500 wheel center cap. - Matt

 

I don't think it's the one I need, but not sure. Here is a pic of the one I'm looking for. 428 SCJ.

http://members.cox.net/detailshop/manual/93.jpg

Pic curtousy of Joe Sikora.